Stanley Meyer Gas Feedback

Control Circuit-GMS Gas Management System

 

Thee Gas Feed Back circuit was originally part of the VIC Matrix set of boards to control the throttling of gas production and ramping up of gas production in line wwith pedal position and gas pressure.

Hydrogen Hot Rodders Do it again 

A flip-flop relay might work a a easy fit

to have 2 cell side by side maintaining pressuree to the fuel rail. 2 to 6 bar depending on engine.

The dual-pump compressors 

(for run-time leveling) aren't even energized all the time.

When the pressure switch triggers a compressor to run,

it'll run until the pressure switch tells it to cut off.

Just as a 2 bar cell prssure switch transducer would just adjust it .

At the same time it triggers, it sends a pulse to the flip-flop

relay so the next time, the other compressor runs.

so both cell hit pressure  say 2 bar than turn off only one is oppen to fuel rail, once it drop beloww 1 bar the flip activate clse low cell to start producing and open the high prressure cell to release its gas to rail. this is better than having a buffer tank on the rail.

The flip-flop relays have a vertical spring and a sort of detent mechanism,

 

so a short pulse through the coil on either side will flip it to that side and it'll stay there even when the coils are             de-energized. GOD Seeed Water is Fuel

Also See Pneumatically Piloted Flip-Flop Valve

Pressure Sensor

On Version1 and Version 2

Operating Range 0 to 6 bar is what we need this sensor works but we should select careefully , the more pressure to fuel rail the better if using gas, if using Nano bubble water version than just 1 - 2 atm ok . 

Transducer for Monitoring Water Cell Pressure

Omega Precise Measurement Quality transducer Reads PRESSURE AND DETERMINED BY PRESSURE, ADAPTS induction RESISTANCE, AND OSCILLATIONS INPUT PULSE SO WE HAVE A CONSTANT gas production

PX176-015A5V

•±1% Interchangeability

•Sealed for Harsh Environments

•1 to 6 Vdc Output

•9 to 20 Vdc Power

•-55 to 105°C Operating Range

•Fully Calibrated and Temperature Compensated

 

SPECIFICATIONSExcitation: 9 to 20 Vdc at 15 mA (polarity protection)

Output: 1 to 6 Vdc

Input Resistance: 2 MΩ at 25 Vdc

PERFORMANCEAccuracy: ±1.0% full scale

Linearity: ±0.5% full scale

Hysteresis: ±0.25% full scale

Zero Balance: ±1% full scaleSpan

Tolerance: 5 ±0.1 Vdc

Operating Temperature Range: -55 to 105°C (-67 to 221°F)

Compensated Temperature Range: 0 to 85°C (32 to 185°F)

Thermal Zero Effect: ±0.02% rdg/°C (±0.01% rdg/°F)

Thermal Sensitivity Effect: ±0.02% rdg/°C (±0.01% rdg/°F)

Proof Pressure: 2x full scale; 1.5x over 200 psi

Burst Pressure: 20x full scale; 10x: 50 to 200 psi; 5x: 500 psi and up

CONSTRUCTIONGages: Piezoresistive on bending beam

Body/Diaphragm Material: 300 Series SS (silver, copper, nickel, cadmium brazed)

Pressure Port: 1/8-27 NPTELECTRICAL CONNECTIONCable Style: 900 mm (36") 3-lead shielded PVC

Pressure Cavity Volume: 0.091 in³Weight: 113 g (4 oz)Frequency Response: 50 Hz

 

http://www.omega.com/pptst/PX176.html

Version 1

Version 1 which we feel was in the GMS box perhaps the Version 1 GMS 

Th Water Fuel Faries Found the Substitue Sheet from the Patent Applications. 

So with your help we have already rebuilt this card t words as described and can be purchsed now from Secure Supplies with Gauge and sender. 

This card out put to gauge , Vic Driver filter board and the Gate Board.

 

The Gas feedback control circuit. 


1: It has the pressure transducer hooked to it.
2: It maintains a certain low pressure limit.
3: If the pressure gets to a certain high pressure limit

     it turns the cell off.
4: It also has a pressure gauge hooked to it so you can

    see the pressure in the cell.

 
5: If the pressure gets to a certain high pressure limit it

    turns the cell off.
 

 

 I count 6 op-amps, 3 PLLs, 2 one-shots and 2 quad nor gates.

 electrostatic filter boards also controlled the cell water level and stuff i think. Seemed like there were quite a few more parts on the board than in the schematic. 

 

Maybe Stan had it built for dual control or something, multiple chambers if needed.

 Seemed like there were quite a few more parts on the board than in the schematic.  Maybe Stan had it built for dual control or something, multiple chambers if needed.

 

I have this photos also. It is electrostatic filter boards - according to name of photos I have.

 

I dont remember  where I got this photos and dont know who give this name.that also controlled the cell water level and stuff

Like Electrostatic Filter

Order Now 

Gas Feed Back Circuit 

$100   

Version 2

Version 2 which we feel was in the GMS box was this card, though

we a building it now to check operational Parameters 

It is Possible this card was designed to controls 4 cells or 4 relays handling voltage from ceenter taps or individual vic matix sets.

Help Speed this Up

Tip Us Please

$10  $25    $50   $100   $250  $500

About Us

Secure Supplies Media Group is

an international collective of Hot Rodders photographers, writers & drivers with a shared passion for promoting the world's most exciting

Hydrogen car culture stories.

Contact Us

We're always very interested to hear your own stories as well as to receive your feedback.

Please New Members first but if you don't find what you are looking for then you are welcome to contact us via email, thank you.

Secure Supplies  Social

 Facebook- @SecureSupplies

 Twitter      @SecureSupplies

 Instagram - SecureSupplies​

 Pinterest   - Secure.Supplies

 Minds         - SecureSupplies 

 Youtube       - SecureSupplies

Tip Us Please

$10  $25    $50   $100   $250  $500

Team Secure

Editor in Chief: Daniel Donatelli 
Senior Editor: Simone White
Editor at Large: Johny Case
Commercial Director: Willem Coetzee
Community Manager: Ryan
Butters
Technical Editor: Jason Nash
Concept Artist:  Samuel Hill
Senior Contributors:  Jacky Bright
Contributors:  Sally Smith, Joanne Livey, Bruce Smith.

Event Partners

Untitled.png

Automotive Partners

Back to Main Site 

www.securesupplyusa.com

logo.jpg

Merchandise Partners

Manufacturing  Partners

Manufacturing.png

Wechat

Whatsapp

Line

Skype

Secure Supplies Energy Power Gas Magazine ™

All Rights Reserved Worldwide. Copyright © 2012 Secure Supplies Limited Daniel Donatelli © 2009 

TRADEMARKS BELONG TO THEIR RESPECTIVE OWNERS. ALL RIGHTS RESERVED

 No duplication is permitted of this site graphically or
conceptually unless requested and approved in writing.

TERMS OF SERVICE // PRIVACY & COOKIE POLICY // LEGAL NOTICES // ADVERTISING OPPORTUNITIES

Work with us Employment